www.RiversideRenegades.com

Home of Riverside Renegades Paintball
It is currently Sat Dec 31, 2016 1:43 pm

All times are UTC - 5 hours




Post new topic Reply to topic  [ 1 post ] 
Author Message
PostPosted: Thu Jul 21, 2005 8:13 pm 
Offline
User avatar

Joined: Fri Sep 17, 2004 5:23 pm
Posts: 214
Location: Everywhere on the Feild
I got this off of pbnation, I thought it was intresting so i posted it. :D

Shaving:
Time required: about 30-60 minutes. You can use a sharp knife that you periodically heat-up to slice through the rubber webbing. I used an exacto knife (no heat) to cut the rubber off. Try to get as close to the plastic shell, but don't worry if some rubber remains...you'll take care if it in the next step.

Smoothing:
Time required: about 4 days (1 day if you are very experienced with auto body repair, but then you probably wouldn't need these instruction!).
1) Use masking tape to cover all holes on the bottom and the front of the shell. Tape from the inside of the shell so the sticky side of the tape is facing outwards.
2) Use coarse grit (~60-80) sand paper to take off the remaining rubber and roughen up the plastic.
3) Use high grit (~120) sand paper to smooth out the roughness.
4) Apply a thin layer of Bondo brand Glazing and Spot Putty. This comes in a tube - no mixing required. Let dry a few hours. Sand down with 120-150 grit sand paper.
5) Apply another thin layer of Putty, let dry, then sand with 200 grit sand paper.
6) Apply another thin layer of Putty, let dry, then wet sand with 400 grit sand paper.
The "shell" should now be nice and smooth to the touch and to look at. If any imperfections still exist, repeat step 6 until smoothed out.

Painting:
Time required: 1-3 days, depending if you are applying more than one color.
1) Spray 2 light coats of Krylon Fusion paint to the shell, waiting 20-30 minutes between coats.
2) Wait to dry 1 hour, then wet sand with 400 grit sand paper.
3) Repeat steps 1-2.
4) Spray 4 more coats, let dry overnight.
Skip steps 5-6 if you only want a solid color, then go to step 7.
5) If you want to add stripes or another color, use the blue 14-day painters tape to cover the areas you do not want to get repainted. This tape will make clean lines, but still remove easily, without residue, within a few days of placement.
6) Spray 2-4 thin coats of the new color/stripes. Let dry overnight, then remove tape carefully.
7) Spray 6 thin coats of (any brand) clear coat, allowing to dry between coats per manufacturer's directions.

Supplies and Cost:
Xacto Knife $1
Wet/dry sand paper, assorted grit $4
Sanding Brick (optional) $3
Bondo brand Glazing and Spot Putty $2
Applicator/plastic spatula (or get one from the kitchen) $1
Blue Painter's Tape $2
Krylon Fusion Paint $4 per color
Clear Coat Paint $1

_________________
SwAGGeR at One Zero Zero and climbing.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1 post ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group