www.RiversideRenegades.com

Home of Riverside Renegades Paintball
It is currently Sat Dec 31, 2016 1:41 pm

All times are UTC - 5 hours




Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: Phantom Pump
PostPosted: Fri May 05, 2006 11:01 am 
Offline
User avatar

Joined: Fri Sep 17, 2004 5:23 pm
Posts: 214
Location: Everywhere on the Feild
Finally I got my primary gun set up and enjoy it I was intrested in a

Phantom. I was looking at the Micro Phantom or a acid wash green

Phantom. My question was for a barrel to accel and be accurate at any

resonable distance doesnt need to have a barrel longer than 6in? I

thought that you atleast needed 8in.

_________________
SwAGGeR at One Zero Zero and climbing.


Top
 Profile  
 
 Post subject:
PostPosted: Fri May 05, 2006 12:14 pm 
Offline
Site Admin
User avatar

Joined: Wed Dec 31, 1969 7:00 pm
Posts: 1304
Location: Finleyville, PA (outside the PGH taxes!)
For best consistency and efficiency you should have 6-8 inches of good fitting barrel.

As for anything else on a Phantom... its a very basic gun. Anything stock from CCI is going to be cosmetic, but work well.

Punisher over at Punisher's Customs (www.punishers-customs.com) has some very nice additions for phantoms, some of them are sold over at Air Soldier Products (http://airsoldier.com/)

Also around are the Carter machine guns (Like the Comp, Buzzard, Termite) who were being sold by Dye for a while. Good stuff, high priced.. but good stuff.

Lapco is also doing a re-make of the Grey Ghost which should come out some time in the next year, I hear they are shipping now. Internals are all Lapco (high efficiency) and gun now takes a spyder threaded barrel.

(Just a few things to think about, maybe give you options. Do remember though, CCI has about the BEST customer service in the PB industry)

_________________
Later,
Bryan "Azzy" Spiegel
www.riversiderenegades.com
[url:3eidvjl2]http://www.PaintBallCity.org[/url:3eidvjl2]


Top
 Profile  
 
 Post subject:
PostPosted: Sat Nov 18, 2006 1:36 am 
Offline
Site Admin
User avatar

Joined: Mon Feb 02, 2004 12:59 am
Posts: 121
Location: Santa Clara, CA
stock phantom barrels, 8" or 11" work for me without a problem. Purchase the tiny little inserts to deal with small paint that's around, and start goggling.

Seriously, I've had no problems with the stock barrels other than roll out. Which you shouldn't get with the inserts. Or you can paint nail polish around on the inside to create a "widget" like device.

I have the old urban camo setup, acid wash stuff looks pretty nice. If you want a hopper, get a center feed body. The right feed bodies with modern hoppers are balanced wrong. The gun weighs less then a fully loaded hopper.

When I ran it with something larger, I used a WGP reg on it, but mostly so I had something to grab on the front. The gun is quite consistant.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group